Evaluación de la resistencia al desgaste y corrosión en recubrimientos (TI,W,SI)N con adición de Ni depositados mediante - co-sputtering

Vista sencilla de ítem
dc.contributor.advisorOlaya Florez, Jhon Jairo
dc.contributor.authorGonzález González, Edwin Ricardo
dc.contributor.researchgroupGrupo de Investigación Afis (Análisis de Fallas, Integridad y Superficies)spa
dc.date.accessioned2023-01-18T21:05:00Z
dc.date.available2023-01-18T21:05:00Z
dc.date.issued2022-12-21
dc.descriptionilustraciones, fotografías principalmente a blanco y negrospa
dc.description.abstractEn la presente investigación se estudió la influencia de la adición de níquel en películas de WTiSiN depositadas mediante el proceso co-sputtering reactivo empleando una configuración de dos blancos. Se utilizaron como sustratos los aceros H13 y 4340 para evaluar las propiedades tribológicas de los recubrimientos y la aleación de titanio Ti6Al4V para evaluar las propiedades anticorrosivas. Las caracterizaciones microestructurales y morfológicas se llevaron a cabo mediante difracción de rayos X (DRX) y microscopia electrónica de barrido (SEM), respectivamente. La caracterización química elemental se efectuó por medio de espectroscopia de rayos X de energía dispersiva (EDS). El comportamiento frente al desgaste se evaluó por medio del ensayo de Ball on disc, logrando obtener los coeficientes de fricción (COF) y la tasa de desgaste. El comportamiento frente a la corrosión se evaluó mediante polarización potenciodinámica (TAFEL) y espectroscopia de impedancia electroquímica (EIS). Los recubrimientos mostraron cambios en la estructura y morfología debido a la adición de níquel, así como una disminución en el coeficiente de fricción. Sin embargo, el comportamiento frente a la corrosión fue inferior al del sustrato de la aleación Ti6Al4V. (Texto tomado de la fuente)spa
dc.description.abstractIn the present investigation, the influence of nickel addition on WTiSiN films deposited by reactive co-sputtering using a two-target configuration was studied. H13 and 4340 steels were used as substrates to evaluate the tribological properties of the coatings and the titanium alloy Ti6Al4V to evaluate the anticorrosive properties. The microstructural and morphological characterizations were carried out by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Elemental chemical characterization was performed by energy dispersive X-ray spectroscopy (EDS). The behavior against wear was evaluated by means of the Ball on disc test, obtaining the coefficients of friction (COF) and the rate of wear. Corrosion behavior was evaluated by potentiodynamic polarization (TAFEL) and electrochemical impedance spectroscopy (EIS). The coatings showed changes in structure and morphology due to the addition of nickel, as well as a decrease in the coefficient of friction. However, the corrosion behavior was inferior to that of the Ti6Al4V alloy substrate.eng
dc.description.degreelevelMaestríaspa
dc.description.degreenameMagister en Ingeniería de Materiales y Procesosspa
dc.description.researchareaIngeniería de Superficiesspa
dc.format.extentvii, 97 páginasspa
dc.format.mimetypeapplication/pdfspa
dc.identifier.instnameUniversidad Nacional de Colombiaspa
dc.identifier.reponameRepositorio Institucional Universidad Nacional de Colombiaspa
dc.identifier.repourlhttps://repositorio.unal.edu.co/spa
dc.identifier.urihttps://repositorio.unal.edu.co/handle/unal/83019
dc.language.isospaspa
dc.publisherUniversidad Nacional de Colombiaspa
dc.publisher.branchUniversidad Nacional de Colombia - Sede Bogotáspa
dc.publisher.facultyFacultad de Ingenieríaspa
dc.publisher.placeBogotá, Colombiaspa
dc.publisher.programBogotá - Ingeniería - Maestría en Ingeniería - Materiales y Procesosspa
dc.relation.referencesH. A. Macías, L. Yate, L. E. Coy, J. J. Olaya, and W. Aperador, “Effect of nitrogen flow ratio on microstructure , mechanical and tribological properties of TiWSiN x thin film deposited by magnetron co-sputtering,” Appl. Surf. Sci., vol. 456, no. January, pp. 445–456, 2018.spa
dc.relation.referencesH. A. Macías, L. Yate, L. E. Coy, W. Aperador, and J. J. Olaya, “Influence of Si-addition on wear and oxidation resistance of TiWSi x N thin films,” Ceram. Int., vol. 45, no. February, pp. 17363–17375, 2019.spa
dc.relation.referencesG. Greczynski, S. Mráz, L. Hultman, and J. M. Schneider, “Unintentional carbide formation evidenced during high-vacuum magnetron sputtering of transition metal nitride thin films,” Appl. Surf. Sci., vol. 385, pp. 356–359, 2016.spa
dc.relation.referencesS. Mitrovic, D. Adamovic, F. Zivic, D. Dzunic, and M. Pantic, “Friction and wear behavior of shot peened surfaces of 36CrNiMo4 and 36NiCrMo16 alloyed steels under dry and lubricated contact conditions,” Appl. Surf. Sci., vol. 290, pp. 223–232, 2014.spa
dc.relation.referencesA. Inspektor and P. A. Salvador, “Architecture of PVD coatings for metalcutting applications: A review,” Surf. Coatings Technol., vol. 257, pp. 138–153, 2014.spa
dc.relation.referencesS. Veprek and A. S. Argon, “Mechanical properties of superhard nanocomposites,” Surf. Coat. Technol., vol. 147, pp. 175–182, 2001.spa
dc.relation.referencesV. Chawla, R. Jayaganthan, and R. Chandra, “A study of structural and mechanical properties of sputter deposited nanocomposite Ti – Si – N thin fi lms,” Surf. Coat. Technol., vol. 204, no. 9–10, pp. 1582–1589, 2010.spa
dc.relation.referencesC. Karvánková, P., Mannling, H.D., Eggs and S. Veprek, “Thermal stability of ZrN – Ni and CrN – Ni superhard nanocomposite coatings,” Surf. Coat. Technol., vol. 147, pp. 280–285, 2001.spa
dc.relation.referencesS. Veprek and S. Reiprich, “A concept for the design of novel superhard coatings,” Thin Solid Films, vol. 268, pp. 64–71, 1995.spa
dc.relation.referencesT. Sato, M. Tada, and Y. C. Huang, “PHYSICAL VAPOR DEPOSITION OF CHROMIUM AND TITANIUM NITRIDES BY THE HOLLOW CATHODE DISCHARGE PROCESS,” Thin Solid Films, vol. 54, pp. 61–65, 1978.spa
dc.relation.referencesD. . Matthews, A, Teer, “EVALUATION OF COATING WEAR RESISTANCE FOR BULK METAL FORMING,” Thin Solid Films, vol. 73, pp. 315–321, 1980.spa
dc.relation.referencesE. Buhl, R., Pulker, H.K, Moll, “TiN COATINGS ON STEEL,” Thin Solid Films, vol. 80, pp. 265–270, 1981.spa
dc.relation.referencesH. A. Colorado, “Damping behavior of physical vapor-deposited TiN coatings on AISI 304 stainless steel and adhesion determinations,” Mater. Sci. Eng. A, vol. 442, pp. 514–518, 2006.spa
dc.relation.referencesY. X. Ou, J. Lin, S. Tong, H. L. Che, W. D. Sproul, and M. K. Lei, “Wear and corrosion resistance of CrN / TiN superlattice coatings deposited by a combined deep oscillation magnetron sputtering and pulsed dc magnetron sputtering,” Appl. Surf. Sci., vol. 351, pp. 332–343, 2015.spa
dc.relation.referencesH. Wang, R. Zhang, Z. Yuan, X. Shu, E. Liu, and Z. Han, “A comparative study of the corrosion performance of titanium ( Ti ), titanium nitride ( TiN ), titanium dioxide ( TiO 2 ) and nitrogen-doped titanium oxides ( N – TiO 2 ), as coatings for biomedical applications,” Ceram. Int., vol. 41, no. 9, pp. 11844–11851, 2015.spa
dc.relation.referencesJ. Castanho and A. Cavaleiro, “Study of tungsten sputtered films with low nitrogen content,” Vacuum, vol. 45, no. 93, pp. 1051–1053, 1994.spa
dc.relation.referencesT. Polcar, N. M. G. Parreira, and A. Cavaleiro, “Tribological characterization of tungsten nitride coatings deposited by reactive magnetron sputtering,” Wear, vol. 262, pp. 655–665, 2007.spa
dc.relation.referencesT. Polcar, N. M. G. Parreira, and A. Cavaleiro, “Structural and tribological characterization of tungsten nitride coatings at elevated temperature,” Wear, vol. 265, pp. 319–326, 2008.spa
dc.relation.referencesT. Polcar and A. Cavaleiro, “Structure , mechanical properties and tribology of W – N and W – O coatings,” Int. J. Refract. Met. Hard Mater., vol. 28, no. 1, pp. 15–22, 2010.spa
dc.relation.referencesV. Tiron, I. Laura, C. Porosnicu, I. Burducea, P. Dinca, and P. Malinsk, “Tungsten nitride coatings obtained by HiPIMS as plasma facing materials for fusion applications,” Appl. Surf. Sci., vol. 416, pp. 878–884, 2017.spa
dc.relation.referencesH. Zhao and F. Ye, “Effect of Si-incorporation on the structure , mechanical , tribological and corrosion properties of WSiN coatings,” Appl. Surf. Sci., vol. 356, pp. 958–966, 2015.spa
dc.relation.referencesF. Diserens, M., Patscheider, J., Lévy, “Mechanical properties and oxidation resistance of nanocomposite TiN – SiNx physical-vapor-deposited thin films,” Surf. Coat. Technol., vol. 121, pp. 158–165, 1999.spa
dc.relation.referencesS. Zhang, D. Sun, Y. Fu, H. Du, and Q. Zhang, “Effect of sputtering target power density on topography and residual stress during growth of nanocomposite nc-TiN/a-SiNxthin films,” Diam. Relat. Mater., vol. 13, no. 10, pp. 1777–1784, 2004.spa
dc.relation.referencesS. Zhang, D. Sun, Y. Fu, Y. T. Pei, and J. T. M. De Hosson, “Ni-toughened nc-TiN/a-SiNx nanocomposite thin films,” Surf. Coatings Technol., vol. 200, no. 5–6, pp. 1530–1534, 2005.spa
dc.relation.referencesV. Chawla, R. Jayaganthan, and R. Chandra, “Influence of Sputtering Pressure on the Structure and Mechanical Properties of Nanocomposite Ti-Si-N Thin Films,” J. Mater. Sci. Technol., vol. 26, no. 8, pp. 673–678, 2010.spa
dc.relation.referencesC. K. Chung, H. C. Chang, S. C. Chang, and M. W. Liao, “Evolution of enhanced crystallinity and mechanical property of nanocomposite Ti-Si-N thin films using magnetron reactive co-sputtering,” J. Alloys Compd., vol. 537, pp. 318–322, 2012.spa
dc.relation.referencesQ. Wan et al., “Corrosion behaviors of TiN and Ti-Si-N ( with 2 . 9 at .% and 5 . 0 at .% Si ) coatings by electrochemical impedance spectroscopy,” Thin Solid Films, vol. 616, pp. 601–607, 2016.spa
dc.relation.referencesH. T. Wang, Y. X. Xu, and L. Chen, “Optimization of Cr-Al-N coating by multilayer architecture with TiSiN insertion layer,” J. Alloys Compd., vol. 728, pp. 952–958, 2017.spa
dc.relation.referencesL. . Shaginyan, M. Misina, J. Zemek, J. Musil, F. Regent, and V. F. Britun, “Composition , structure , microhardness and residual stress of W – Ti – N films deposited by reactive magnetron sputtering,” Thin Solid Films, vol. 408, pp. 136–147, 2002.spa
dc.relation.referencesR. . Londoño-Menjura, R. Ospina, D. Escobar, J. H. Quintero, J. J. Olaya, and A. Mello, “Influence of deposition temperature on WTiN coatings tribological performance,” Appl. Surf. Sci., vol. 427, pp. 1096–1104, 2018.spa
dc.relation.referencesE. Grigore, A. A. El Mel, A. Granier, and P. Y. Tessier, “The influence of Ni content on the characteristics of C – Ni thin films,” Surf. Coat. Technol., vol. 211, pp. 188–191, 2012.spa
dc.relation.referencesJ. F. Yang, Y. Jiang, R. F. Yang, Y. X. Gao, X. P. Wang, and Q. F. Fang, “Microstructure and mechanical properties of W – Ni – N coatings prepared by magnetron sputtering,” Thin Solid Films, vol. 570, pp. 249–255, 2014.spa
dc.relation.referencesL. B. Varela, F. Fernandes, A. Cavaleiro, and A. P. Tschiptschin, “NbC-Ni coatings deposited by DC reactive magnetron sputtering : E ff ect of Ni content on mechanical properties , thermal stability and oxidation resistance,” Surf. Coat. Technol., vol. 349, no. June, pp. 1018–1031, 2018.spa
dc.relation.referencesD. S. Belov et al., “Abrasive , hydroabrasive , and erosion wear behaviour of nanostructured ( Ti , Al ) N-Cu and ( Ti , Al ) N-Ni coatings,” Surf. Coat. Technol., vol. 338, no. February, pp. 1–13, 2018.spa
dc.relation.referencesJ. Yi, S. Chen, K. Chen, Y. Xu, Q. Chen, and C. Zhu, “Effects of Ni content on microstructure , mechanical properties and Inconel 718 cutting performance of AlTiN-Ni nanocomposite coatings,” Ceram. Int., no. August, pp. 0–1, 2018.spa
dc.relation.referencesC. Sha, P. Munroe, Z. Zhou, and Z. Xie, “Effect of Ni content on the microstructure and mechanical behaviour of CrAlNiN coatings deposited by closed fi eld unbalanced magnetron sputtering,” Surf. Coat. Technol., vol. 357, no. October 2018, pp. 445–455, 2019.spa
dc.relation.referencesZ. R. Liu, B. Peng, Y. X. Xu, Q. Zhang, Q. Wang, and L. Chen, “Influence of Ni-addition on mechanical , tribological properties and oxidation resistance of AlCrSiN coatings,” Ceram. Int., vol. 45, no. October 2018, pp. 3735–3742, 2019.spa
dc.relation.referencesE. N. Borja-goyeneche and J. J. Olaya-florez, “A microstructural and corrosion resistance study of ( Zr , Si , Ti ) N-Ni coatings produced through co-sputtering • Un estudio de la microestructura y resistencia a la corrosión de recubrimientos de ( Zr , Si , Ti ) N-Ni producidas mediante co- sputtering,” Dyna, vol. 85, no. 207, pp. 192–197, 2018.spa
dc.relation.referencesASM International, Metals HandBook VOL 2, Properties and Selection: Nonferrous Alloys and Special-Purpose Materials. 1990.spa
dc.relation.referencesASTM International, “Designation: B265-13a StandardSpecification for Titanium and Titanium Alloy Strip , Sheet , and Plate,” pp. 1–10, 2020.spa
dc.relation.referencesASTM International, “Designation: A681-08 StandardSpecification for Tool Steels Alloy,” pp. 1–14, 2020.spa
dc.relation.referencesS. Kumar, D. Singh, and N. S. Kalsi, “Analysis of Surface Roughness during Machining of Hardened AISI 4340 Steel using Minimum Quantity lubrication,” Mater. Today Proc., vol. 4, no. 2, pp. 3627–3635, 2017.spa
dc.relation.referencesASTM International, “Designation: A29/A29M-15 Standard Specification for General Requirements for Steel Bars , Carbon and Alloy ,” pp. 1–16, 2020.spa
dc.relation.referencesJ. E. Greene, “1800s to 2017 Review Article : Tracing the recorded history of thin-film sputter deposition : From the 1800s to 2017,” J. Vac. Sci. Technol., vol. 204, no. 2017, pp. 1–61, 2018.spa
dc.relation.referencesH. Wasa, Kiyotaka, Kanno, Isaku, Kotera, Handbook of Sputter Deposition Technology - Fundamentals and applications for functional Thin Films, Nanomaterials, and MEMS, 2nd ed. 2012.spa
dc.relation.referencesD. M. Mattox, Handbook of Physical Vapor Deposition (PVD) Processing, Second edi. 2010.spa
dc.relation.referencesD. Nilsson and U. Wiklund, “A flexible laboratory-scale approach to alloying and tailoring of thin films by single-magnetron co-sputtering,” Thin Solid Films, vol. 467, pp. 10–15, 2004.spa
dc.relation.referencesA. Buranawong, N. Witit-anun, S. Chaiyakun, A. Pokaipisit, and P. Limsuwan, “The effect of titanium current on structure and hardness of aluminium titanium nitride deposited by reactive unbalanced magnetron co-sputtering,” Thin Solid Films, vol. 519, no. 15, pp. 4963–4968, 2011.spa
dc.relation.referencesA. Kumar, Lahiri, Applied Metallurgy and Corrosion Control - A Handbook for the Petrochemical Industry. Springer, 2017.spa
dc.relation.referencesM. M. T. Luque, “ESTUDIO COMPARATIVO DEL PROCESO DE CORROSIÓN EN RECUBRIMIENTOS CERÁMICOS, METÁLICOS Y ORGÁNICOS MEDIANTE TÉCNICAS ELECTROQUÍMICAS,” 2010.spa
dc.relation.referencesASM International, ASM Metals Handbook Volume 13, Corrosion. 1987.spa
dc.relation.referencesASTM International, “Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements,” vol. 89, no. Reapproved 2010. pp. 1–7, 2012.spa
dc.relation.referencesASTM International, “Standard Reference Test Method for Making Potentiostatic and Potentiodynamic Anodic Polarization Measurements,” vol. 94, no. Reapproved 2011, pp. 1–12, 2012.spa
dc.relation.referencesC. Liu, Q. Bi, A. Leyland, and A. Matthews, “An electrochemical impedance spectroscopy study of the corrosion behaviour of PVD coated steels in 0.5 N NaCl aqueous solution : Part II . EIS interpretation of corrosion behaviour,” Corros. Sci., vol. 45, pp. 1257–1273, 2003.spa
dc.relation.referencesGamry Instruments, “The basics of Electrochemical Impedance Spectroscopy.” p. 18.spa
dc.relation.referencesGamry Instruments, “EIS of Coated Metals.” p. 16.spa
dc.relation.referencesB. Orazem, Mark E., Tribollet, Electrochemical Impedance Sepctroscopy. Jhon Wiley & Sons, Inc., 2008.spa
dc.relation.referencesC. Liu, Q. Bi, A. Leyland, and A. Matthews, “An electrochemical impedance spectroscopy study of the corrosion behaviour of PVD coated steels in 0.5 N NaCl aqueous solution : Part I . Establishment of equivalent circuits for EIS data modelling,” Corros. Sci., vol. 45, pp. 1243–1256, 2003.spa
dc.relation.referencesM. Patiño Infante, “EVALUACION DEL COEFICIENTE DE FRICCIÓN Y LAS PROPIEDADES MECÁNICAS DE LOS RECUBRIMIENTOS 140MXC-530AS Y 140MXC-560AS SOBRE ACERO AISI-SAE 4340 UTILIZANDO LA TÉCNICA DE PROYECCIÓN TÉRMICA,” 2015.spa
dc.relation.referencesJ. R. Davis, SURFACE ENGINEERING FOR CORROSION AND WEAR RESISTANCE. 2001.spa
dc.relation.referencesR. C. Vega-morón et al., “Adhesion and mechanical properties of Ti fi lms deposited by DC magnetron sputtering,” Surf. Coat. Technol., vol. 349, no. May, pp. 1137–1147, 2018.spa
dc.relation.referencesASTM International, “Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus,” vol. 05, no. Reapproved, pp. 1–5, 2016.spa
dc.relation.referencesA. A. Gómez Zapata, “Determinación de propiedades estructurales y esfuerzos residuales de películas delgadas de YBaCo 4 O 7 + δ depositadas sobre sustratos monocristalinos por técnica de pulverización catódica,” 2014.spa
dc.relation.referencesW. . Oliver and G. . Pharr, “An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments,” Mater. Res. Soc., vol. 7, pp. 1564–1583, 1992.spa
dc.relation.referencesO. A. T. MONTERO, “CRECIMIENTO Y CARACTERIZACIÓN DE PELICULAS DELGADAS DE NITRURO DE TITANIO CIRCONIO (Ti,Zr)N,” 2009.spa
dc.relation.referencesF. Gao, G. Li, and Y. Xia, “Influence of hysteresis effect on properties of reactively sputtered TiAlSiN films,” Appl. Surf. Sci., vol. 431, pp. 160–164, 2018.spa
dc.relation.referencesS. Berg and T. Nyberg, “Fundamental understanding and modeling of reactive sputtering processes,” Thin Solid Films, vol. 476, pp. 215–230, 2005.spa
dc.relation.referencesSAFINA a.s., “Because everything needs to be just right,” 2017. [Online]. Available: https://www.tescan.com/because-everything-needs-to-be-just-right/.spa
dc.relation.referencesH. Antonio and E. Puentes, “Producción y caracterización de bicapas de DLC / Zr x O y usando técnicas de sputtering y CVD asistido por plasma,” 2017.spa
dc.relation.referencesGamry Instruments, “Over 27 years of Redefining Electrochemical Measurements.” pp. 0–24.spa
dc.relation.referencesL. A. Cañon Tafur, “PROPIEDADES ANTICORROSIVAS DE RECUBRIMIENTOS TixAlySizN ELABORADOS POR EL SISTEMA DE SPUTTERING REACTIVO,” 2017.spa
dc.relation.referencesJ. H. Quintero and H. Leyton, “Análisis del ensanchamiento de las líneas de difracción de Bragg de la fase cúbica fcc del oro,” Inventum, vol. 11, no. 11, pp. 6–10, 2011.spa
dc.relation.referencesA. Ruden Muñoz, “ANALISIS ESTRUCTURAL, SUPERFICIAL Y TRIBOLOGICO DE RECUBRIMIENTOS DE NITRURO DE CROMO (CrN) SINTETIZADO POR MAGNETRON SPUTTERING REACTIVO DC,” 2011.spa
dc.relation.referencesD. H. Buckley, Surface effects in adhesion, friction, wear, and lubrication. Elsevier, 1981.spa
dc.relation.referencesJ. Newell, Ciencia de Materiales Aplicaciones en Ingenieria. Alfaomega, 2011.spa
dc.relation.referencesL. V. Estrada, “Producción , Caracterizacion Microestructural y Estudio de la Resistencia a la Corrosión de Recubrimientos Nanoestructurados de Nb x Si y N z Depositados con el Sistema de UBM . Producción , Caracterizacion Microestructural y Estudio de la Resistencia a l,” 2011.spa
dc.relation.referencesS. J. Splinter, R. Rofagha, N. S. McIntyre, and U. Erb, “XPS Characterization of the Corrosion Films Formed on Nanocrystalline Ni-P Alloys in Sulphuric Acid,” Surf. interface Anal., vol. 24, pp. 181–186, 1996.spa
dc.relation.referencesM. Kalisz, M. Grobelny, D. Kaczmarek, J. Domaradzki, M. Mazur, and D. Wojcieszak, “Comparison of structural , mechanical and corrosion properties of TiO2 -WO3 mixed oxide films deposited on TiAlV surface by electron beam evaporation,” Appl. Surf. Sci., vol. 421, pp. 185–190, 2017.spa
dc.relation.referencesD. Javdo, J. Musil, Z. Soukup, S. Haviar, R. Č, and J. Houska, “Tribological properties and oxidation resistance of tungsten and tungsten nitride fi lms at temperatures up to 500 ° C,” Tribol. Int., vol. 132, no. October 2018, pp. 211–220, 2019.spa
dc.relation.referencesX. Xiao and B. Yao, “Structure and oxidation resistance of W 1−x AlxN composite films,” Trans. Nonferrous Met. Soc. China (English Ed., vol. 27, pp. 1063–1070, 2017.spa
dc.relation.referencesASM International, ASM Handbook Volume 13A - Corrosion: Fundamentals, Testing, and Protection. 2003.spa
dc.relation.referencesG. Palumbo and K. T. Aust, “Triple-line Corrosion in High Purity Nickel *,” Mater. Sci. Eng., vol. 113, pp. 139–147, 1989.spa
dc.relation.referencesK. T. Palumbo, G., Aust, “Localized corrosion at grain boundary intersections in high purity nickel,” Scr. Metall., vol. 22, pp. 0–5, 1988.spa
dc.relation.referencesK. T. Palumbo, G., Thorpe, S.J., Aust, “ON THE CONTRIBUTION OF TRIPLE JUNCTIONS TO THE STRUCTURE AND PROPERTIES OF NANOCRYSTALLINE MATERIALS,” Nanocrystalline Mater., vol. 24, no. 1, pp. 1347–1350, 1990.spa
dc.relation.referencesN. P. Wasekar, N. Hebalkar, A. Jyothirmayi, B. Lavakumar, and M. Ramakrishna, “Influence of pulse parameters on the mechanical properties and electrochemical corrosion behavior of electrodeposited Ni-W alloy coatings with high tungsten content,” Corros. Sci., vol. 165, no. December 2019, p. 108409, 2020.spa
dc.relation.referencesZ. V. Riveros, “ESTUDIO DE LA RESISTENCIA AL DESGASTE DE PELÍCULAS DELGADAS DE Ti,” 2006.spa
dc.relation.referencesI. Ponomarev, T. Polcar, and P. Nicolini, “Tribological properties of V2O5 studied via reactive molecular dynamics simulations,” Tribol. Int., vol. 154, no. October 2020, pp. 1–11, 2021.spa
dc.relation.referencesM. Ermrich and D. Opper, X-RAY Powder Diffraction for the analyst, Second Edi. Almelo, Netherlands: PANalytical GmbH, 2011.spa
dc.relation.referencesM. Monsalve, E. López, J. Meza, and F. Vargas, “Estudio mediante difracción de rayos X de las tensiones residuales producidas durante el depósito de películas delgadas de TiN sobre sustratos metálicos,” Revista Facultad de Ingenieria, no. 54, pp. 32–41, 2010.spa
dc.relation.referencesJ. H. Quintero, J. A. Peñafiel Castro, and H. Leyton, “Análisis del ensanchamiento de las líneas de difracción de Bragg de la fase cúbica fcc del oro,” INVENTUM, vol. 6, no. 11, pp. 6–10, Jul. 2011, doi: 10.26620/uniminuto.inventum.6.11.2011.6-10.spa
dc.relation.referencesMa. L. Ramón García, “Determinación del tamaño de cristal utilizando el software Jade 6.5,” Centro de Investigación en energía, Ciudad de México, 2007. [Online]. Available: https://xml.cie.unam.mx/xml/ms/Doctos/ManualJade65.pdfspa
dc.rights.accessrightsinfo:eu-repo/semantics/openAccessspa
dc.rights.licenseAtribución-NoComercial 4.0 Internacionalspa
dc.rights.urihttp://creativecommons.org/licenses/by-nc/4.0/spa
dc.subject.ddc080 - Colecciones generalesspa
dc.subject.lembRevestimientos protectoresspa
dc.subject.lembProtective coatingseng
dc.subject.lembCubiertas protectorasspa
dc.subject.lembProtective converingseng
dc.subject.proposalWTiSiN-Nispa
dc.subject.proposalco-sputteringeng
dc.subject.proposalpolarización potenciodinámicaspa
dc.subject.proposalespectroscopía de impedancia electroquímicaspa
dc.subject.proposaltasa de desgaste.spa
dc.titleEvaluación de la resistencia al desgaste y corrosión en recubrimientos (TI,W,SI)N con adición de Ni depositados mediante - co-sputteringspa
dc.title.translatedEvaluation of the resistance to wear and corrosion in coatings (TI,W,SI)N with addition of Ni deposited by co-sputteringeng
dc.typeTrabajo de grado - Maestríaspa
dc.type.coarhttp://purl.org/coar/resource_type/c_bdccspa
dc.type.coarversionhttp://purl.org/coar/version/c_ab4af688f83e57aaspa
dc.type.contentTextspa
dc.type.driverinfo:eu-repo/semantics/masterThesisspa
dc.type.redcolhttp://purl.org/redcol/resource_type/TMspa
dc.type.versioninfo:eu-repo/semantics/acceptedVersionspa
dcterms.audience.professionaldevelopmentBibliotecariosspa
dcterms.audience.professionaldevelopmentEstudiantesspa
dcterms.audience.professionaldevelopmentInvestigadoresspa
dcterms.audience.professionaldevelopmentMaestrosspa
dcterms.audience.professionaldevelopmentPúblico generalspa
oaire.accessrightshttp://purl.org/coar/access_right/c_abf2spa
oaire.awardtitleEVALUACIÓN DE LA RESISTENCIA AL DESGASTE Y CORROSIÓN EN RECUBRIMIENTOS (TI,W,SI)N CON ADICIÓN DE Ni DEPOSITADOS MEDIANTE– CO-SPUTTERINGspa

Archivos

Bloque original

Mostrando 1 - 1 de 1
Miniatura
Nombre:
80832677.2022.pdf
Tamaño:
4.01 MB
Formato:
Adobe Portable Document Format
Descripción:
Tesis de Maestría en Ingeniería - Materiales y Procesos
Descargar

Bloque de licencias

Mostrando 1 - 1 de 1
No hay miniatura disponible
Nombre:
license.txt
Tamaño:
5.74 KB
Formato:
Item-specific license agreed upon to submission
Descripción:
Descargar

Colecciones

Maestría en Ingeniería - Materiales y Procesos